Active axis X=0 Y=0 Z=1 
Current Position X=2.5928 Y=147.1708 Z=12.5600 
Distance Mode = 1 
Command Pos X=2.5928 Y=147.1708 Z=-7.4400 
################# Probe Started at 20 Hours 54 Min 55 Sec ####################
Current Position X=2.5928 Y=147.1708 Z=12.5600 A=0.0000  
Probe to X=2.5928 Y=147.1708 Z=-7.4400 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=0.0000 Y=-0.0000 Z=-20.0000 A=0.0000
Probe Distance = 20.0000
Move Time = 3.4286
Probe Decel start(counts) X=45229 Y=19822 Z=-8183 A0 
Probe move direction X=0 Y=1 Z=1 A0 
Probe Vector X=0.0000 Y=-0.0000 Z=-2000.0000 
Probe Angles Before probe r=2000.0000 phi=3.1416 theta=-1.5708 
Engine.LastPosition X=2.5928 Y=147.1708 Z=-7.4400 A0.0000 

##########  Probe Finished at 20 Hours 54 Min 55 Sec ##########
Probe Activated = 1
Probe tripped at (Counts) X=45229 Y=19823 Z=-6221 A=0.0000
Engine.LastPosition X=2.5928 Y=147.1708 Z=5.7800 A0.0000 
Probe Finished axis pos X=2.5928 Y=147.1708 Z=12.5200 A=0.0000



Probe rad Vector X=0.0000 Y=-0.0000 Z=-1.5000 
Probe Finish pos With Rad X=2.5928 Y=147.1708 Z=14.0200 
Active axis X=1 Y=0 Z=0 
Current Position X=2.5928 Y=147.1708 Z=17.5200 
Distance Mode = 1 
Command Pos X=-59.9072 Y=147.1708 Z=17.5200 
################# Probe Started at 20 Hours 55 Min 01 Sec ####################
Current Position X=2.5928 Y=147.1708 Z=17.5200 A=0.0000  
Probe to X=-59.9072 Y=147.1708 Z=17.5200 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=-62.5000 Y=-0.0000 Z=-0.0000 A=0.0000
Probe Distance = 62.5000
Move Time = 10.7143
Probe Decel start(counts) X=28015 Y=19822 Z=-5721 A0 
Probe move direction X=1 Y=1 Z=1 A0 
Probe Vector X=-17307.6923 Y=-0.0000 Z=-0.0000 
Probe Angles Before probe r=17307.6923 phi=1.5708 theta=-3.1416 
Engine.LastPosition X=-59.9072 Y=147.1708 Z=17.5200 A0.0000 

##########  Probe Finished at 20 Hours 55 Min 01 Sec ##########
Probe Activated = 0
Probe tripped at (Counts) X=27922 Y=19823 Z=-5721 A=0.0000
Engine.LastPosition X=-59.9047 Y=147.1708 Z=17.5200 A0.0000 
Probe Finished axis pos X=-59.9047 Y=147.1708 Z=17.5200 A=0.0000



Probe rad Vector X=-1.5000 Y=-0.0000 Z=-0.0000 
Probe Finish pos With Rad X=-61.4047 Y=147.1708 Z=17.5200 
Active axis X=0 Y=0 Z=1 
Current Position X=-59.9047 Y=147.1708 Z=17.5200 
Distance Mode = 1 
Command Pos X=-59.9047 Y=147.1708 Z=9.5200 
################# Probe Started at 20 Hours 55 Min 12 Sec ####################
Current Position X=-59.9047 Y=147.1708 Z=17.5200 A=0.0000  
Probe to X=-59.9047 Y=147.1708 Z=9.5200 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=0.0000 Y=-0.0000 Z=-8.0000 A=0.0000
Probe Distance = 8.0000
Move Time = 1.3714
Probe Decel start(counts) X=27922 Y=19822 Z=-6487 A0 
Probe move direction X=0 Y=1 Z=1 A0 
Probe Vector X=0.0000 Y=-0.0000 Z=-800.0000 
Probe Angles Before probe r=800.0000 phi=3.1416 theta=-1.5708 
Engine.LastPosition X=-59.9047 Y=147.1708 Z=9.5200 A0.0000 

##########  Probe Finished at 20 Hours 55 Min 12 Sec ##########
Probe Activated = 0
Probe tripped at (Counts) X=27922 Y=19823 Z=-6531 A=0.0000
Engine.LastPosition X=-59.9047 Y=147.1708 Z=9.4200 A0.0000 
Probe Finished axis pos X=-59.9047 Y=147.1708 Z=9.4200 A=0.0000



Probe rad Vector X=0.0000 Y=-0.0000 Z=-1.5000 
Probe Finish pos With Rad X=-59.9047 Y=147.1708 Z=10.9200 
Active axis X=1 Y=0 Z=0 
Current Position X=-59.9047 Y=147.1708 Z=9.4200 
Distance Mode = 1 
Command Pos X=55.0953 Y=147.1708 Z=9.4200 
################# Probe Started at 20 Hours 55 Min 15 Sec ####################
Current Position X=-59.9047 Y=147.1708 Z=9.4200 A=0.0000  
Probe to X=55.0953 Y=147.1708 Z=9.4200 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=115.0000 Y=-0.0000 Z=0.0000 A=0.0000
Probe Distance = 115.0000
Move Time = 19.7143
Probe Decel start(counts) X=59674 Y=19822 Z=-6531 A0 
Probe move direction X=0 Y=1 Z=0 A0 
Probe Vector X=31846.1538 Y=-0.0000 Z=0.0000 
Probe Angles Before probe r=31846.1538 phi=1.5708 theta=-0.0000 
Engine.LastPosition X=55.0953 Y=147.1708 Z=9.4200 A0.0000 
Active axis X=0 Y=0 Z=1 
Current Position X=0.0000 Y=0.0000 Z=0.0000 
Distance Mode = 1 
Command Pos X=0.0000 Y=0.0000 Z=-20.0000 
################# Probe Started at 20 Hours 56 Min 02 Sec ####################
Current Position X=0.0000 Y=0.0000 Z=0.0000 A=0.0000  
Probe to X=0.0000 Y=0.0000 Z=-20.0000 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=0.0000 Y=0.0000 Z=-20.0000 A=0.0000
Probe Distance = 20.0000
Move Time = 3.4286
Probe Decel start(counts) X=45123 Y=19823 Z=-8497 A0 
Probe move direction X=0 Y=0 Z=1 A0 
Probe Vector X=0.0000 Y=0.0000 Z=-2000.0000 
Probe Angles Before probe r=2000.0000 phi=3.1416 theta=0.0000 
Engine.LastPosition X=0.0000 Y=0.0000 Z=-20.0000 A0.0000 

##########  Probe Finished at 20 Hours 56 Min 02 Sec ##########
Probe Activated = 1
Probe tripped at (Counts) X=45123 Y=19823 Z=-6535 A=0.0000
Engine.LastPosition X=0.0000 Y=0.0000 Z=-3.6700 A0.0000 
Probe Finished axis pos X=0.0000 Y=0.0000 Z=-0.0400 A=0.0000



Probe rad Vector X=0.0000 Y=0.0000 Z=-1.5000 
Probe Finish pos With Rad X=0.0000 Y=0.0000 Z=1.4600 
Active axis X=1 Y=0 Z=0 
Current Position X=0.0000 Y=0.0000 Z=4.9600 
Distance Mode = 1 
Command Pos X=-62.5000 Y=0.0000 Z=4.9600 
################# Probe Started at 20 Hours 56 Min 07 Sec ####################
Current Position X=0.0000 Y=0.0000 Z=4.9600 A=0.0000  
Probe to X=-62.5000 Y=0.0000 Z=4.9600 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=-62.5000 Y=0.0000 Z=0.0000 A=0.0000
Probe Distance = 62.5000
Move Time = 10.7143
Probe Decel start(counts) X=27909 Y=19823 Z=-6035 A0 
Probe move direction X=1 Y=0 Z=0 A0 
Probe Vector X=-17307.6923 Y=0.0000 Z=0.0000 
Probe Angles Before probe r=17307.6923 phi=1.5708 theta=3.1416 
Engine.LastPosition X=-62.5000 Y=0.0000 Z=4.9600 A0.0000 

##########  Probe Finished at 20 Hours 56 Min 07 Sec ##########
Probe Activated = 0
Probe tripped at (Counts) X=27816 Y=19823 Z=-6035 A=0.0000
Engine.LastPosition X=-62.4975 Y=0.0000 Z=4.9600 A0.0000 
Probe Finished axis pos X=-62.4975 Y=0.0000 Z=4.9600 A=0.0000



Probe rad Vector X=-1.5000 Y=0.0000 Z=0.0000 
Probe Finish pos With Rad X=-63.9975 Y=0.0000 Z=4.9600 
Active axis X=0 Y=0 Z=1 
Current Position X=-62.4975 Y=0.0000 Z=4.9600 
Distance Mode = 1 
Command Pos X=-62.4975 Y=0.0000 Z=-3.0400 
################# Probe Started at 20 Hours 56 Min 18 Sec ####################
Current Position X=-62.4975 Y=0.0000 Z=4.9600 A=0.0000  
Probe to X=-62.4975 Y=0.0000 Z=-3.0400 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=0.0000 Y=0.0000 Z=-8.0000 A=0.0000
Probe Distance = 8.0000
Move Time = 1.3714
Probe Decel start(counts) X=27816 Y=19823 Z=-6800 A0 
Probe move direction X=0 Y=0 Z=1 A0 
Probe Vector X=0.0000 Y=0.0000 Z=-800.0000 
Probe Angles Before probe r=800.0000 phi=3.1416 theta=0.0000 
Engine.LastPosition X=-62.4975 Y=0.0000 Z=-3.0400 A0.0000 

##########  Probe Finished at 20 Hours 56 Min 18 Sec ##########
Probe Activated = 0
Probe tripped at (Counts) X=27816 Y=19823 Z=-6877 A=0.0000
Engine.LastPosition X=-62.4975 Y=0.0000 Z=-3.4600 A0.0000 
Probe Finished axis pos X=-62.4975 Y=0.0000 Z=-3.4600 A=0.0000



Probe rad Vector X=0.0000 Y=0.0000 Z=-1.5000 
Probe Finish pos With Rad X=-62.4975 Y=0.0000 Z=-1.9600 
Active axis X=1 Y=0 Z=0 
Current Position X=-62.4975 Y=0.0000 Z=-3.4600 
Distance Mode = 1 
Command Pos X=52.5025 Y=0.0000 Z=-3.4600 
################# Probe Started at 20 Hours 56 Min 21 Sec ####################
Current Position X=-62.4975 Y=0.0000 Z=-3.4600 A=0.0000  
Probe to X=52.5025 Y=0.0000 Z=-3.4600 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=115.0000 Y=0.0000 Z=0.0000 A=0.0000
Probe Distance = 115.0000
Move Time = 19.7143
Probe Decel start(counts) X=59568 Y=19823 Z=-6877 A0 
Probe move direction X=0 Y=0 Z=0 A0 
Probe Vector X=31846.1538 Y=0.0000 Z=0.0000 
Probe Angles Before probe r=31846.1538 phi=1.5708 theta=0.0000 
Engine.LastPosition X=52.5025 Y=0.0000 Z=-3.4600 A0.0000 

##########  Probe Finished at 20 Hours 56 Min 21 Sec ##########
Probe Activated = 1
Probe tripped at (Counts) X=30416 Y=19823 Z=-6877 A=0.0000
Engine.LastPosition X=-52.7692 Y=0.0000 Z=-3.4600 A0.0000 
Probe Finished axis pos X=-53.1086 Y=0.0000 Z=-3.4600 A=0.0000



Probe rad Vector X=1.5000 Y=0.0000 Z=0.0000 
Probe Finish pos With Rad X=-51.6086 Y=0.0000 Z=-3.4600 
Active axis X=1 Y=0 Z=0 
Current Position X=-58.1086 Y=0.0000 Z=4.5400 
Distance Mode = 1 
Command Pos X=53.8914 Y=0.0000 Z=4.5400 
################# Probe Started at 20 Hours 56 Min 28 Sec ####################
Current Position X=-58.1086 Y=0.0000 Z=4.5400 A=0.0000  
Probe to X=53.8914 Y=0.0000 Z=4.5400 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=112.0014 Y=0.0000 Z=0.0000 A=0.0000
Probe Distance = 112.0014
Move Time = 19.2002
Probe Decel start(counts) X=59952 Y=19823 Z=-6077 A0 
Probe move direction X=0 Y=0 Z=0 A0 
Probe Vector X=31015.7693 Y=0.0000 Z=0.0000 
Probe Angles Before probe r=31015.7693 phi=1.5708 theta=0.0000 
Engine.LastPosition X=53.8928 Y=0.0000 Z=4.5400 A0.0000 

##########  Probe Finished at 20 Hours 56 Min 28 Sec ##########
Probe Activated = 0
Probe tripped at (Counts) X=60047 Y=19823 Z=-6077 A=0.0000
Engine.LastPosition X=53.8922 Y=0.0000 Z=4.5400 A0.0000 
Probe Finished axis pos X=53.8922 Y=0.0000 Z=4.5400 A=0.0000



Probe rad Vector X=1.5000 Y=0.0000 Z=0.0000 
Probe Finish pos With Rad X=55.3922 Y=0.0000 Z=4.5400 
Active axis X=0 Y=0 Z=1 
Current Position X=53.8922 Y=0.0000 Z=4.5400 
Distance Mode = 1 
Command Pos X=53.8922 Y=0.0000 Z=-3.4600 
################# Probe Started at 20 Hours 56 Min 48 Sec ####################
Current Position X=53.8922 Y=0.0000 Z=4.5400 A=0.0000  
Probe to X=53.8922 Y=0.0000 Z=-3.4600 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=0.0000 Y=0.0000 Z=-8.0000 A=0.0000
Probe Distance = 8.0000
Move Time = 1.3714
Probe Decel start(counts) X=60047 Y=19823 Z=-6843 A0 
Probe move direction X=0 Y=0 Z=1 A0 
Probe Vector X=0.0000 Y=0.0000 Z=-800.0000 
Probe Angles Before probe r=800.0000 phi=3.1416 theta=0.0000 
Engine.LastPosition X=53.8922 Y=0.0000 Z=-3.4600 A0.0000 

##########  Probe Finished at 20 Hours 56 Min 48 Sec ##########
Probe Activated = 0
Probe tripped at (Counts) X=60047 Y=19823 Z=-6910 A=0.0000
Engine.LastPosition X=53.8922 Y=0.0000 Z=-3.7900 A0.0000 
Probe Finished axis pos X=53.8922 Y=0.0000 Z=-3.7900 A=0.0000



Probe rad Vector X=0.0000 Y=0.0000 Z=-1.5000 
Probe Finish pos With Rad X=53.8922 Y=0.0000 Z=-2.2900 
Active axis X=1 Y=0 Z=0 
Current Position X=53.8922 Y=0.0000 Z=-3.7900 
Distance Mode = 1 
Command Pos X=-61.1078 Y=0.0000 Z=-3.7900 
################# Probe Started at 20 Hours 56 Min 51 Sec ####################
Current Position X=53.8922 Y=0.0000 Z=-3.7900 A=0.0000  
Probe to X=-61.1078 Y=0.0000 Z=-3.7900 A=0.0000
probeA (0.0000) CurrentoriginA (_0.0000)  Steps PerAUnit (1000.0000) AxisCount (0) 
Tool offset X = 0.0000 Z = 0.0000
Distance to move per axis X=-115.0000 Y=0.0000 Z=0.0000 A=0.0000
Probe Distance = 115.0000
Move Time = 19.7143
Probe Decel start(counts) X=28294 Y=19823 Z=-6909 A0 
Probe move direction X=1 Y=0 Z=0 A0 
Probe Vector X=-31846.1538 Y=0.0000 Z=0.0000 
Probe Angles Before probe r=31846.1538 phi=1.5708 theta=3.1416 
Engine.LastPosition X=-61.1078 Y=0.0000 Z=-3.7900 A0.0000 
